The NexWaveRF based 700mW 2.4GHz audio/video transmitter greatly increases the range of your video link, adding a margin of security over commonly used 5.8GHz transmitters. Team this TX up with either a Duo2400 or Uno2400 for amazing image quality and range. Built on the same game changing NexWaveRF technology that has made the ImmersionRC 5.8GHz transmitters such a renowned success the 2.4GHz audio/video transmitter is built on this proven technology to offer you the best possible image quality, durability and ease of use. Sporting roughly the same size and weight as the ImmersionRC's 5.8GHz audio/video transmitters the new 2.4GHz audio/video transmitter brings a few features to market that will allow you to further reap the benefits of choosing ImmersionRC's equipment for your next FPV mission. The 5V output has been beefed up to handle up to 1.5A of current output, which means you can power, and charge, your HD camera such as a Mobius, straight off of our audio/video transmitter. So no more fiddling with external 5V supplies, just hook it up and be done with it. The new 700mW 2.4GHz transmitter is designed to run straight off of your main flight-pack and supports a wide voltage input range of 6-25V (2~6s) direct. Due to its extremely low-noise, highly efficient switching regulator, there's no additional heat being generated when running off of higher voltages and the switching regulator's input is well filtered to cope with noise from your speed controller, or other electronics connected within your aircraft. The NexWaveRF based 2.4GHz audio/video transmitter has a 700mW/28.5dB RF output power, putting it a notch above the commonly available 500mW 2.4GHz transmitters from other manufacturers. It features the same industry standard locking connectors for connecting your battery and camera or audio/video source as featured on ImmersionRC's other products. This makes the new 2.4GHz audio/video transmitter fully compatible with the existing 5.8GHz audio/video transmitters; it can be swapped out directly as all the connectors, and connector pin-outs, are the same. This also applies to the SMA-female antenna connector used. Features: ? 700mW transmitting power (can be used license-free in Europe) ? NexwaveRF based ? 5V 1.5A output for FPV camera and charging ? Small Size ? SMA Antenna Connector ? Onboard quiet switching regulator 2~6s direct capable Specs: RF Module: NexwaveRF Power supply: 6~25V (2S-6S supply) Power out (to camera): 5V, 1.5A max Transmitting power: 700mW Operating Frequency: 2.4GHz (2410,2430,2450,2470,2370,2390,2490,2510) Dimensions: 57 X 23 X 12 mm Weight: 18g (without dipole antenna) Note: White connector on the back of the transmitter is for connecting an ImmersionRC TinyTelemetry accessory. (adds Telemetry data to the audio channel for Antenna tracking)
This equipment is being sold under the FCC’s amateur radio rules. Operators must abide by all applicable laws and hold an amateur license to operate this equipment. Use of amateur equipment without a license or use of equipment on restricted frequencies could subject the operator to significant fines by the FCC. By purchasing this equipment, the user is agreeing that they understand these responsibilities and will operate the equipment legally. For information regarding obtaining an amateur radio license, please go to http://www.arrl.org/getting-licensed.
The use and operation of this product in your country may require an amateur radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the purchase and use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. Excel Drones, LLC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.